HTTP Error 500.19 Win 10

If you are having a problem using Vault, post a message here.

Moderator: SourceGear

Post Reply
DTSSL
Posts: 2
Joined: Fri Dec 02, 2016 4:31 pm

HTTP Error 500.19 Win 10

Post by DTSSL » Fri Dec 02, 2016 4:45 pm

Hi - I've read as many posts about this error as I could find, but no solution mentioned has worked for me yet. My details:

- Windows 10, freshly installed IIS with no other web apps installed
- installing: 12/01/2016 05:55 PM 40,278,528 VaultServer64_9_1_0_584.msi
- I've run installer by starting a cmd prompt with admin rights
- chose default install, IIS located at default c:\inetpub\wwwroot
- using Windows auth


URL trying to load:
http://adam/VaultService/VaultWeb/Login ... %20install.

Error information:
Error Code 0x80070021
Config Error This configuration section cannot be used at this path. This happens when the section is locked at a parent level. Locking is either by default (overrideModeDefault="Deny"), or set explicitly by a location tag with overrideMode="Deny" or the legacy allowOverride="false".
Config File \\?\C:\inetpub\wwwroot\VaultService\web.config
Physical Path C:\inetpub\wwwroot\VaultService\VaultWeb\Login.aspx

Can't think of anything else you might need. Any ideas?

DTSSL
Posts: 2
Joined: Fri Dec 02, 2016 4:31 pm

Re: HTTP Error 500.19 Win 10

Post by DTSSL » Mon Dec 05, 2016 10:41 am

I finally found the solution to my problem. Hopefully this will help someone else, as I didn't find any mention of this in the install instructions. Again, this is Win10.

i had to go into Control Panel, Turn Windows Features On or Off, .NET Framework 4.6 Advanced Services, WFC Services, and turn on all the features listed below there. I don't know which one specifically fixed it, it might be only HTTP Activation, but I just turned them all on, and then the Vault Admin Page would load correctly.

jclausius
Posts: 3683
Joined: Tue Dec 16, 2003 1:17 pm
Location: SourceGear
Contact:

Re: HTTP Error 500.19 Win 10

Post by jclausius » Tue Dec 06, 2016 8:20 am

Good find! Do you think it might have been related to this KB article - http://support.sourcegear.com/viewtopic ... 740#p73740 ?

( Looks like it has not yet been updated for Windows 10. )
Jeff Clausius
SourceGear

Balvert
Posts: 2
Joined: Thu Jan 08, 2009 1:20 am

Re: HTTP Error 500.19 Win 10

Post by Balvert » Thu Dec 29, 2016 9:10 am

It seems HTTP Activation fixed the issue.

Rene

Wiffle
Posts: 1
Joined: Mon Feb 13, 2017 2:50 am

Re: HTTP Error 500.19 Win 10

Post by Wiffle » Mon Feb 13, 2017 11:54 pm

DTSSL wrote:I finally found the solution to my problem. Hopefully this will help someone else, as I didn't find any mention of this in the install instructions. Again, this is Win10.

i had to go into Control Panel, Turn Windows Features On or Off, .NET Framework 4.6 Advanced Services, WFC Services, and turn on all the features listed below there. I don't know which one specifically fixed it, it might be only HTTP Activation, but I just turned them all on, and then the Vault Admin Page would load correctly.
Thanks DTSSL that fixed it for me too but I don't know if this is a permanent solution.
This is my Noocube success story so check it out.

jclausius
Posts: 3683
Joined: Tue Dec 16, 2003 1:17 pm
Location: SourceGear
Contact:

Re: HTTP Error 500.19 Win 10

Post by jclausius » Tue Feb 14, 2017 10:29 am

Vault does not have any direct code which uses WCF, but there could be something in the .NET Frameworks that require activation. Glad everyone has it sorted out.
Jeff Clausius
SourceGear

Post Reply